The purpose of this paper is to investigate the relationship between the Ultrasonic Pulse Velocity (UPV) and the compressive strength and the flexural strength of hardened concrete when subjected to different concentrations of sulfate attacks. The specimens used in the studies were made of concrete with different water-cement ratios (w/c). The UPV measurement and compressive and flexural strengths tests were carried out for concrete specimens of ages (4-40) days. The experimental results show that the relationship between UPV and the compressive and the flexural strengths of concrete is significantly influenced by age and the concentration of sulfate attack. The UPV and the compressive strength of concrete grow with age, but the growth rate varies with w/c ratio. It is found that with the same concentration of sulfate attack, a clear relationship curve can be drawn to describe the UPV and compressive and flexural strengths of hardened concrete. This paper presents the UPV-strength relationship curves for concrete having different (w/c) ratios subjected to different concentrations of sulfate attack. These curves are thought to be suitable for prediction of hardened concrete strength with a measured UPV value when sulfate attack is considered. It is concluded that the UPV increases with the increase of the compressive and flexural strength. The observed range for UPV was (3.5 to 4.75 km/sec) corresponds to (24 to 28.5 N/mm2) for compressive strength and to (4.6 to 6.5 N/mm2) for flexural strength. The UPV decreases with the increase of the concentration of sulfate exposure. The obtained maximum reduction in UPV was 31.6% with respect to the control spacemen at age of 40 days.
This study program has been conducted to investigate the influence of adding waste plastic fibers (WPF) resulting from manual cutting for bottles used in the conservation gassy beverage on different characteristics of ordinary concrete. Cutting plastic waste by volumetric rates ranging between (0.5%) to (2%) was approved. Reference mix was produced for comparison. Tests were conducted on the models produced from waste plastic fiber concrete like compressive strength, flexural strength and splitting tensile strength. The analysis of the results showed that the use of plastic waste fibers (1%) has led to improve the properties of flexural strength and splitting tensile strength compared with reference concrete .When the( 0.75%)WPF ratio improved the compressive strength as compared with the control specimen . Compressive strength in (28 days) with fiber ratio (0.75%) WPF is higher than equal (5.1%) from compressive strength in (28 days) of reference concrete. Volumetric ratio (1%) WPF can be also observed that each of the flexural strength and splitting tensile strength increases equal (12.5 and 12.5%) respectively, from flexural strength and splitting tensile strength for the reference mix at(28day).
This research includes producing compacted concrete by rolling method and the possibility for using in highway construction field with studying the influence of adding waste plastic fiber resulting from manual cutting for bottles used in the conservation gassy beverage on different characteristics of this type of concrete. For the purpose of selecting mix proportions appropriate for rolling compacted concrete (RCC). Approved design method for ACI-committee (5R-207 .1980) was selected for this research. Destroying plastic waste by volumetric rates ranging between (0.5%) to (2%) was approved. Reference mix was produced for comparison. Tests were conducted on the models produced from rolling compacted concrete like compressive strength, flexural strength and split tensile strength. The analysis of the results showed that the use of plastic waste fibers (1%) has led to improve the properties of each of the compressive strength and flexural strength and split tensile strength compared with reference concrete. Compressive strength in 28 days with fiber ratio (1%) is higher than (52.15%) from compressive strength in 28 days of reference concrete. It can be also observed that each of the flexural strength and split tensile strength increases by (17.86, 25.61)%, respectively, from flexural strength and split tensile strength for the reference mix
AbstractThis research includes the study of the effect of adding steel fibres resulting from cutting chicken wire (which is available in Iraqi markets now) as fibres added to the polymer concrete. These fibres were added with percentages of concrete volumes. These percentages were (0.5%) and (1%). Reference concrete mix was also made for comparative reasons. From the results, it can be noted that the increasing of compressive strength of SFPC1 comparing with RPC at 28 days equal to 9.90%, whereas the increasing of compressive strength of SFPC2 comparing with RPC at 28 days is equal to 15.48%. The increasing of splitting strength of SFPC1 comparing with RPC at 28 days equal to 15.50%, whereas the increasing of SFPC2 comparing with RPC at 28 days is equal to 21.40%. The increasing of flexural strength of SFPC1 comparing with RPC at 28 days equal to 10.80%, whereas the increasing of SFPC2 comparing with RPC at 28 days is equal to 20.63%.Results proved that adding of steel fibres with these percentages lead to improvements in compressive strength, splitting strength and flexural strength of concretes containing steel fibres, but the improvement in flexural strength appeared more clearly. Results proved also an increasing in densities of fibre concrete samples according to these made of reference mix.
ABSTRACT:The resistance of concrete to sulfate attack is considered as one of the important factors for concrete durability.The effect of SBR polymer on sulfate resistance of concrete is investigated. Both internal and external sulfate attack are considered.Internal sulfate attack was made by adding gypsum to raise the sulfate content of sand to that of Ramadi city soil (2.17%), while the external sulfate attack was made by adding chemical materials (MgSO4.7H2O, Na2SO4, CaCl2.2H2O, NaCl) to tap water to convert it into water similar to groundwater of Ramadi city.The laboratory tests were compressive and flexural strength, modulus of elasticity, slump, ultra-sound velocity and total percentage of sulfate after exposing to attack for different ages. It was found that the compressive strength of reinforced normal concrete (RNC) for ages (7,28,90,180) days respectively were (20,28,11.166,7) MPa, the compressive strength of polymer Portland cement concrete( PPCC) with polymer/cement ratio( P/C)=5% (PPCC5) were (21.83,32.666,12.766,8.733) MPa and for PPCC with (P/C)=10% were (24.166,35.866,15.533,11.366)MPa.While the flexural strength of RNC for different ages (7,28,90,180) respectively were (3.953,3.7,1.68,11.305) MPa, the flexural strength of PPCC5 were (4.05,5.025,2.13,1.605) MPa and for PPCC10 were (4.43,6.375,2.43,1.92) MPa.The static modulus of elasticity at age (28) days for (RNC) was (37.4) GPa , for PPCC5 was (9.7) GPa and for PPCC10 was (13.63) GPa.Slump for (RNC) was (155) mm, for PPCC5 was (142) mm and for PPCC10 was (75) mm.T he ultra-sound velocity of RNC for ages (7,28,90,180) respectively were (4.2,4.445,4.203,4.53) Km/sec , for PPCC5 were (4.36,4.646,4.53,4.176) Km/sec and for PPCC10 were (4.437,4.837,4.656,4.52) Km/sec.It was found that (PPCC10) has higher resistance to sulfate attack than (PPCC5) and (NRC). The thesis refers to necessity of polymer to improve the resistance of concrete to sulfate attack although if the sulfate percentage raise to more than (0.5) % which represents the maximum limit of sulfate percentage in I.O.S No. 45-1970.
Slurry infiltrated fiber concrete (SIFCON) is a relatively new high performance material and can be considered a special type of fiber concrete (FRC) with high fiber content. The matrix consists of a flowing mortar or cement slurry that must penetrate well through the network of fibers placed in the mold. SIFCON has excellent mechanical properties combined with high ductility and toughness values. SIFCON a relatively new material, is composed of mud (cement or cement and sand), water, a plasticizer (water reducer), and fibers. All previous studies have used waste steel fibers, steel fibers and other fibers, but in this study, plastic fibers were made from polyethylene terephthalate (PET) by cutting carbonated beverage bottles. The main objectives of this study are: Determination the effect of the waste plastic fiber volume ratio on the strength and deformation of (SIFCON) samples under the influence of bending loads. Both flexural strength and toughness properties were determined by testing samples (100×100×400) mm at 28 and 56 days of age. The results obtained from these tests were compared with those performed on conventional tests. Aspect Ratio equal to (36.8) and three volume ratios (3%, 5% and 7%) of the total volume of the concrete mixture were used to add fibers with different volume ratios. A conventional concrete mix was created as a reference for comparison. Bending strength and fresh concrete tests were performed. And compared with the reference mixture and according to the analysis of the results. The results showed an improvement in bending strength .It was found through the flexural examination that the flexural strength of the mixture containing fiber percentage (7%) achieved the highest strength compared to the rest of the ratios used, compared with the reference mixture (Ref.) by (32.25, 27.5)% for ages (28, 56), respectively.
Abstract This research studies the effect of adding steel fiber in two percentage 0.5% and 1% by volume on plain structural lightweight concrete (SLWC) produced by using crushed bricks as coarse lightweight aggregates (LWA) in a lightweight concrete mix designed according to ACI committee 211-2-82 with mix proportion 1:1.12 :3.35 by volume .The wc equal to 0.5 and cement content 550 kgm3. Different tests where performed for fresh and hardened SLWC such slump test ,fresh and hardened unit weight ,compressive strength and two indirect tests of tensile strength (splitting tensile and flexural strength). The results demonstrated that the effect of addition of steel fiber was more pronounced on the tensile strength of SLWC than the compressive strength of such concrete .The maximum increase of compressive ,splitting tensile and flexural strengths at 28-days were 38.8,77.12 and 111.2 % in the SLWC containing 1% fiber. On the other hand the rate of strength gain between 3 and 28 days was constant on compressive strength of plain concrete and that containing steel fiber while this rate was clearly increase on tensile strength especially flexural strength.
Adding fibers to the shotcrete concrete mixes is very important to increase the load carrying capacity, toughness, and reducing crack propagations by bridging the cracks. On the other hand, this fiber has an effect on the fresh and hardened properties of shotcrete. In this study, fresh properties evaluated by using slump flow, , and segregation resistance tests. Hardened properties included testing of air voids, dry density, water absorption, ultrasonic pulse velocity (UPV), compressive strength, and flexural strength. This works including two types of fibers in three forms (waste plastic (PET)fibers only, polypropylene fibers (PP) only, and hybrid fiber (PET and PP)), each form added by three percentages (0.35%, 0.7%, and 1%) by volume.The results showed that the addition of 1% of all types of fiber has a negative impact on fresh properties. Especially in shotcrete containing waste plastic fiber. Also, all specimens containing fibers showed a decrease in the ultrasonic pulse velocity (UPV) and an increase in air voids and water absorption compared to the reference specimens. Also, the results clarify that the addition of waste plastic fiber to shotcrete led to a slight decrease in dry density. The highest increasing in compressive strength of shotcrete recorded by about 8.2% with using 0.35% PP fiber and highest decreasing was 20.9% with using 1% waste plastic fiber. the highest increasing in flexural strength was 62 with using 1% PP fibers.
SUMMARY This research work includes three main experimental stages. The first stage includes the production of foamed concrete. It is divided into two parts; in the first, mixing design (determination of the proportions of the raw materials) according to the required density was presented and in the second part, the mixing procedure has been illustrated. The second stage includes preparation of samples,(i.e. molding, finishing surface, removal from molds and curing). The third stage includes several tests to estimate properties of the final product and factors influencing them . These properties include density , compressive strength , splitting tensile strength and flexural strength. For foamed concrete with 800 kg/m3 density, the 28-day compressive strength is from (1.334 MPa) to (2.323 MPa), while with 1600 kg/m3 density, the strength is from (7.015 MPa) to (9.591 MPa). For 1600 kg/m3 density foamed concrete, the 28-day flexural strength range is from (1.08 MPa) to (2.205 MPa).
The current research’s purpose is to examine how Ultra-High Performance Fiber Concrete (UHPFC) holds up in terms of strength and durability for strengthening purposes. For this reason, the experimental and the theoretical studies in this research attempted to assess different fresh and hardened properties of a variety of ultra-high performance combinations. Steel fibers were utilized to differentiate all of the program's combinations at percentages of 0.25 %, 0.5 %, 0.75 %, 1%, and 1.25 % by volume. Mini flow slump, compressive and flexural strength, ultrasonic pulse velocity, water absorption, and porosity tests were all used to examine the performance of the strength and durability of the material. The findings of this study's trials showed that steel fibers increased the strength of UHPFC. The steel fiber ratio of 1% gave the maximum compressive strength, whereas 1.25 percent yielded the highest flexural strength. Because the fibers function as a bridge, preventing internal breaking, the tensile test results were improved as the proportion of steel fiber rises. Through the use of the multi-objective optimization approach, the optimal ratio of fibers was chosen at the end of the laboratory work since it has the best durability and strength characteristics. Statistical software (Minitab 2018) was used to find the optimal combination of UHPFC that meets all of the requirements. The theoretical selected optimum ratio of 0.77% of fibers obtained from the optimization was evaluated and validated experimentally. The optimized mix provided 90.28 MPa, 14.6 MPa, and 20.2 MPa for compressive, splitting tensile and flexural tests respectively with better durability performance compared to other mixes prepared in this investigation.
This research includes study of the of effect of adding sulphur, which is obtained from Samrraa factory on the properties of concrete like compressive strength, flexural strength and splitting tensile strength. The concrete mixes were: (1:8.5:8.5:7), (1:8.5:8.5:9), (1:8.5:8.5:12) and (1:1.5:3:0) (cement: sand: gravel: sulphur) respectively. The results refer to increasing of compressive strength , flexural strength and splitting tensile strength with increasing of sulphur ratio but increasing decreased at age (28)day with respect to ordinary concrete (sulphur ratio=0%).
A voided slab is an innovative type of reinforced concrete slab system developed recently, that has proven its excellence in terms of its structural, environmental, and economic benefits. The self-weight of a slab can be considerably reduced using different shapes of void formers like spherical, cubical, and donut. All researchers confirm that the self-weight of the slab decreases by up to 40%. Various researchers have carried out experimental and numerical studies for studying one-way flexural strength and punching shear strength of voided reinforced concrete slabs. However, the one-way or two-way flexural strength of the voided slab still needs to be acutely investigated. This paper deals with the survey on many titles of selected high impacted journals to illustrated almost criteria of investigations of these types of slabs. The main outcomes of this paper are the term environmental protection, sustainable and plastic waste reduction had a role not a little in this research, as 16% of the research on this topic were studied. Also, the plastic material governs the subject of the raw materials used to make the voids;43% of researches used this material.
AbstractThis study deals with establishing high-velocity impact properties of polymer –modified concrete (PMC) including Styrene-Butadiene rubber (SBR), with different weight ratios of polymer to cement: 4%, 8% and 12%. Steel fibers were also included. Sixteen (500mm) diameter, (50mm) thick discs for high-velocity impact tests were used. In addition compressive strength, splitting tensile strength, and flexural strength (modulus of rupture) were companionly recorded. In all the tests, concrete was with and without crimped steel fibers of ratio 1% by volume.In investigating high-velocity impact strength, the decrease in projectile penetration depth was (5-17%) and the scabbing area reduced (15-35%) over reference concrete.In studying PMC including 1% by volume steel fibers, an additional increase was observed in all properties. The increases were quite significant in high-velocity impact strengths. Further reduction was recorded in scabbing area of (64-95%) and penetration depth reduced (28-39%) over control specimens. The fragmentations were reduced also. The range of corresponding compressive was (48-64)MPa ,of splitting tensile strength (4.2-7.8) MPa, and of flexural strength (5-8) MP
Concrete is produced from millions of tons of Cement, which emits a significant amount of carbon dioxide from cement mills and contributes to global warming. Therefore, it is important to seek out less expensive and more environmentally friendly substitutes for OPC. While various substitutes are available, such as recycled glass, marble, silica fume fly ash, or agricultural waste like rice husks or wheat straw, the performance of concrete is significantly affected when bentonite is used as a replacement for Cement. This study aims to evaluate Jhelum bentonite, which is located at 32°56′ north and 73°44′ east longitude, as a replacement for Cement in different ratios (0:100, 10:90, 20:80, 30:70, and 40:60) to improve the durability of the system as more bentonite is used to replace conventional Portland cement, the workability, density, and water absorption of the new concrete all decrease. Compressive Strength, Tensile Strength, and flexural Strength of blocks and cylinders were tested after being cured for 7 and 28 days. Analysis of these strength tests revealed that the mixes containing bentonite were weaker after 7 days compared to 28 days, and the Strength of blocks was reasonable compared to cylinders.Keywords: Bentonite, Concrete, Compressive Strength, Tensile Strength.
This research investigates the impact resistance of concrete slabs with different volume perecentage replacement ratios of waste plastic fibers (originaly made from soft drink bottles) as follows : 0.5%, 1% and 1.5%. Reference mix produced in order to compare the result. For the selected mixes, cubes with (100×100×100mm) were made to test compressive strength at age of (90) days. Flexural strength (Modulus of Rupture) test was also conducted using prisms sample of (500*100*100 mm) dimensions. The low-velocity impact test was conducted by the method of repeated falling mass where 1400gm steel ball was used. The ball falling freely from height of 2400mm on concrete panels of (500×500×50 mm) having a mesh of waste plastic fiber.The number of blows that caused first crack and final crack (failure) were determined, according to the former obtained results , the total energy was calculated. Results showed an improvement in mechanical properties for mixes containing plastic fibers compared with reference mix. For compressive strength the maximum increase in compressive strength was equal to (3.2%) at age of (90) days. Flexural strengths for mixes containing plastic fiber at ages 28, and 90 days are higher than that of these of reference mix. The maximum value of increaseing was (18%) for 28 days age of test and it was equal to (26%) for 90 days age of test for the mixture with plastic fiber content by volume equal to (1%) . Results showed a significant improvement in low-velocity impact resistance of all mixes contining waste plastic fibers when comparing with reference mix. Results illustrated that mix with (1.5%) waste plastic fibers by volume give the higher impact resistance at failure than the others. The magnitude of an increase over reference mix was equal to (340%).
This study addressed some important tests for concrete including thermal, acoustic insulation and some mechanical behaviour of concrete containing granular Polyvinyl Chloride (PVC) waste as a sand replacement. The PVC waste was collected from a plant of manufacturing PVC doors and windows, was used to replace some of fine aggregate at ratios of 2.5%, 5%, 7.5%, 10%, 12.5% and 15% by weight Properties that studied are thermal conductivity, acoustic insulation slump, fresh density, dry density, compressive strength, flexural strength, and splitting tensile strength. Curing ages of 7, 28, and 56 days for the concrete mixtures were applied in this work. From the results of this study, it is suggested that using of 12.5% fine PVC as a sand replacement by weight can improve thermal insulation to about 82.48% more than concrete without plastic waste Acoustic insulation is about 43.09% more than reference mix and it satisfies the requirement of ACI 213R 2014 for structural lightweight concrete.
This study presents an experimental research of Self-Compacting Concrete (SCC) properties containing waste plastic fibers (WPF). Adding waste plastics which resulting from cutting PET bottles as fibers to SCC with aspect ratio (l/d) equal to (28). To illustrate the effects of WPFs on the SCC, the current study was divided into two parts, the first part shows the effect of adding plastic fibers on the properties of fresh SCC, which include the ability flow, spread, passing and resistance to segregation, and the second part to evaluate the properties of hardened (mechanical) destructive and non-destructive, which include compression strength, flexural strength and ultrasonic pulse velocity test. One reference concrete mix was conducted and eight mixes contain WPF has been producing self-compacting concrete mixers containing a different volumetric ratio of plastic fibers (Vf) % percentages (0.25, 0.5, 0.75, 1, 1.25, 1.5, 1.75, 2) %. Three cubes samples were prepared for testing the compressive strength, three prisms were prepared for the test modules of rupture, one cylinder were prepared testing the modulus of elasticity. The experiments show that adding plastic fibers to SCC leads to an increase in the compression strength and modulus of rupture at 28-day as follows (42.30)% and (73.12)% respectively for mix ratio (1.5)% in comparison with the reference mix, which represent the best ratio of fibers, as such the results of testing the fresh concrete containing waste fibers showed that adding these fibers led a reduction in workability for SCC.
This study describes the results of tests carried out in order to investigate the structural behavior of reinforced concrete beams containing Expanded Polystyrene (EPS) stabilized Polystyrene beads. Three concrete mixtures were used with densities 350kg/m3, 500 kg/m3 and 600 kg/m3. A total of 12 beams, with control specimens were tested after 28 days of curing immersion in water. Four types of steel reinforcement were utilized: Two ratios of tensile steel reinforcement without compression steel and the same two ratios of tensile reinforcement with compression steel and stirrups. The beams were tested under 4- points loading up to failure. The main variables considered in this study were: different types of Izocrete densities and types of reinforcement steel bars. The results indicated that the amount of polystyrene beads significantly affects the strength of the concrete produced. In general, it can be observed that the compression, tensile and flexure strengths decreased as the EPS beads contents increased, and the moment capacity of the beams reduced with the increase of the beads ratio.The load deflection behavior of the Izocrete beams were similar to other lightweight concrete beams .The failure in most of the beams was initiated at the compression region undergoing large deformation due to the high compressibility of the material.
This research work includes production of new type of light weight concrete and studies the mechanical and thermal properties. Several proportions of raw materials were used to produce this type of concrete. This study is intended to produce light weight concrete with low thermal conductivity so that it can be used for concrete masonry units. Polystyrene aggregate was added as percentages by weight of cement to improve the thermal properties of this type of concrete .Mechanical , and thermal tests with difference ages were made in this work .For polystyrene concrete with polystyrene cement ratio (p/c) of (2.67 – 6 )% , the28-day compressive strength range is from (4.31 – 2.67)MPa, flexural strength range is from (3.05-1.719 ) MPa , density range is from ( 1493-1213 ) kg/m 3 ,and thermal conductivity range is from ( 0.91-0.782)% as a percentage by that of reference mix. The study show suitability of this type of concrete to be used in concrete masonry units of non-bearing walls.
This research includes studying the possibility of producing a new kind of No-fines concrete by replacing granules of coarse aggregates with grains results from the fragmentation of industrial waste of polystyrene. This replacing were with different volumetric proportions of coarse aggregate, and theses volumetric ratios were equal to (5%, 10%, 15% and 25%). Waste plastic fibers (WPFs) resulting from cutting of soft drinks bottles were added for strengthening this new kind of concrete. Mixing ratio was equal to (1:5) (cement: coarse aggregate) by weight. One reference mix was produced for comparative purpose. Compressive strength, flexural strength and density tests were conducted, it was examined three samples of each examination and taking the average. Compressive strength values of the new sustainable concrete were ranged from 10 MPa to 12.4 MPa at age of test equal to 28 days, while the average value of the density of this concrete at the same age reaches 1930 kg/m3. This average value of modulus of rupture was equal to 2.36 MPa at 28-day age test.
Abstract:Many of researchers study the uses of chopped worn-out tires as a replacementmaterial to production special types of concrete. In presented work, the worn-out tireswere used as fibers which have dimensions of 1×1×3 cm. The fibers used as a partialreplacement from volume of coarse aggregate. Two mixes of fiber worn-out tires(F.W.T.) concrete in addition to reference mix were selected, using PartialReplacement Ratio (PRR) of 20% and 30%. The tests which were used in this studywere: compressive strength, splitting tensile strength and flexural strength. It wasfound that incorporating of F.W.T. in concrete effected negatively on most propertiesof concrete, for example the percentage decreases in compressive strength relative toreference mix at 28 day were 20% and 27.3% for concrete with 20% and 30% F.W.T.by volume of coarse aggregate respectively. However, it gave good indicator to beutilized as a new construction material in many applications.
This main aim of this study is evaluate wide range of fresh and hardened properties of sustainable self-compacting concrete containing various types of Cement Replacement Materials with optimum contents of Polyethylene Terephthalate PET waste plastic as fibers and fine aggregate replacement. This is to evaluate effect of the two forms of PET and to determine the best CRMs could be used with sustainable SCC. such as limestone, glass powder and fly ash with high replacement rate of 70% by weight of cement were used while fourth one (kaolin) was used with replacement rate of 20%. PET fibers were added to SCC with an aspect ratio of 24.4 and 0.7% volume fraction whereas fine aggregate partially replaced by 4% of waste plastic. Four reference mixtures contained FA, LP, GP and KA only, same four mixtures contained 0.7% PET fibers by volume, and the other same four mixtures contained 4% PET fine aggregate by volume. The obtained results all tested fresh properties, which include slump flow, T500, L-Box and segregation resistance were within the limits of the specification reported in EFNERC guidelines. Further, the forms PET have an adverse effect fresh properties of SCC. As for hardened properties (compressive strength, splitting tensile strength, flexural strength and impact strength). Further, this produced type of SCC showed an range of compressive strength (15.2-31.64 MPa) at 28 days. It can be from the current study the best CRMs to be used in SCC containing PET wastes was FA in terms of most tested properties.
In this study, eight rectangular reinforced concrete beams strengthened by bottom steel plates firmly interconnected to them by headed-stud shear connectors are manufactured using self compacting concrete and tested up to failure under two point loads to demonstrate the effect of steel-plate thicknesses, lengths, and the shear-connector distributions on the behavior, ductility and strength of this type of beams. A trial mix conforming to the EFNARC Constraints had been successfully carried out to satisfy the three fresh tests of SCC, these tests are flowability, passing ability and segregation resistance. The results show that there is a substantial improvement in the flexural resistance, increasing the flexural stiffness and decreasing the ductility ratio due to thickening steel plate, On contrary, increasing the spacing between shear connectors to 50% had slight effect on the flexural resistance, but subsequent increase of their spacing to 100% had seriously lowered that resistance, The spacing between shear connectors has a primary effect on the average flexural stiffness and ductility ratio. In regard to the steel plate length, its shortening has reduced the flexural resistance significantly, decreased the average flexural stiffness and had increased the ductility ratio. The experimentally determined ultimate flexural strength had been compared with its corresponding one computed by the "Strength Method" using ACI requirements where high agreement gained between them due to the nearly perfect interaction provided by SCC. The eight composite beams had also been analyzed by the non-linear three dimensional Finite Element Analysis employing ANSYS program (release 12.1),where high agreement is achieved compared with experimental results.
The use of externally bonded composite materials such as carbon fiber reinforced polymers (CFRP) sheets is a modern and convenient way for strengthening and repairing reinforced concrete (RC) beams. This study presents experimental investigations on the flexural behavior of reinforced concrete beams strengthened by unsymmetrical CFRP sheets with various configurations. Effects of number of which strengthened faces of strengthening and fiber direction on the flexural strength of RC beams are examined. Six RC beams with dimensions of 100 mm * 220 mm were casted and tested under two points loading. One beam considered as a reference (unstrengthened) beam. Five residual beams were strengthened using CFRP sheets with various configurations. From the results, it was observed that all strengthened beams showed higher ultimate load capacity than that of the control beam. On the other hand, it was found that a progressive reduction in flexural ductility and toughness of beams with strengthening in one face and two faces with horizontal fiber direction. The highest decrease in flexural ductility and toughness for strengthened beams with horizontal fiber direction in comparison to control beam were 63% and 54%, respectively. On the contrary, the flexural ductility and toughness of strengthened beams increased with strengthening by vertical fiber direction. Additionally, the maximum percentage of increase in flexural ductility and toughness were 41% and 54%, respectively in comparison with control beam.
This study was conducted to examine the impact of plastic fibers (WPFs) in an effort to improve some of the features of self-compacting concrete (SCC) using Iraqi raw materials. Waste polyethylene terephthalate fibers (waste PET fibers) from used beverage bottles were added. Some tests were carried out to determine the effects of adding WPFs on the fresh properties of new concrete, while additional tests examined the mechanical properties of hardened concrete. Because of this, self-compacting concrete blends were created with a constant water-to-binder ratio of 0.32 and a binder content of 525 kg/m3. The designated plastic fiber percentages contents were 0%, 0.5%, 0.75%, and 1% of mix volume. Self-compacting concrete mixtures' fresh characteristics were assessed for slump flow diameter, T50 slump flow concurrently, V-funnel flow concurrently, and L-box height ratio. The 28-day density, compressive strengths and flexural strength of self-compacting concretes were also measured. The use of plastic waste fibers had a slight effect on reducing the density of the produced concrete and a negative effect on the fresh properties. The compressive strengths were improved by using WPFs, with the maximum improvement equal to (11.065%) when compared to those made from the reference mix
The aim of this research is to produce lightweight cement mortar with properties better than reference ordinary cement mortar. Porcelanite stone were utilized as lightweight aggregate with a volumetric partial substitution of fine aggregate. The process includes using different percentages (5, 10, 15 and 20 %) of pre-wetted (24hr.) porcelanite to produce lightweight mortar with internal curing. Water curing was used for reference mortar mixture and air curing for the other mixtures of porcelanite substitution. Compressive strength, flexural strength, density and ultrasonic pulse velocity for different ages (7, 14 and 28 days) have been tested. The results show an improvement in the properties of cement mortar especially in replacement percentage of 10 %.
ABSTRACT: Many of researchers study the uses of chopped worn-out tires as a replacement material to production special types of concrete. In presented work, the worn-out tires were used as fibers which have dimensions of 1×1×3 cm. The fibers used as a partial replacement from volume of coarse aggregate. Two mixes of fiber worn-out tires (F.W.T.) concrete in addition to reference mix were selected, using Partial Replacement Ratio (PRR) of 20% and 30%. The tests which were used in this study were: compressive strength, splitting tensile strength and flexural strength. It was found that incorporating of F.W.T. in concrete effected negatively on most properties of concrete, for example the percentage decreases in compressive strength relative to reference mix at 28 day were 20% and 27.3% for concrete with 20% and 30% F.W.T. by volume of coarse aggregate respectively. However, it gave good indicator to be utilized as a new construction material in many applications.